Meal planning

Keep a smoker cook and fuel log you can compare later

On this page · 6 sections

Straight answer

Record the conditions and measurement boundary before calculating a fuel rate. Starting fuel plus additions minus all known remaining fuel can support an inventory calculation; hopper-only leftovers cannot establish the whole cooker’s balance. Keep cook-only time separate from startup-through-shutdown time, and leave incomplete results unknown. [3]

A closed outdoor cooker beside a table with a lidded round metal pan
Locally generated illustration of a closed outdoor cooker beside a table with a lidded round metal pan.

Choose the question your log will answer

This article provides an original blank record, a comparison checklist and three invented arithmetic examples. The source reading establishes limits: Traeger identifies conditions affecting its pellet estimates, its named Pro manual describes hopper-only cleanout, and Weber’s New Zealand guidance allows possible reuse of its briquettes. None supplies a measured result for the fictional cooks below. We performed no cooks, weighed no fuel and tested no efficiency; the calculations are inventory accounting under stated assumptions. [1] [2] [3]

Write the metric before entering numbers. New fuel taken from a bag, total fuel charged including retained fuel, mass returned after a cook, and estimated mass not returned are different quantities. A rate should name both its numerator and its included time. A weight difference does not by itself measure heat delivered to food or chemical combustion efficiency.

On a narrow screen, scroll the table sideways to compare all columns.

Original definitions for interpreting a personal log. Use one mass unit and the same boundary at both ends.
MetricCalculation / requirementWhat it does not establish
New fuel issuedMass of new fuel allocated to this recorded interval.Fuel consumed, if fuel remains afterward or retained fuel was already present.
Fuel not returned to this inventoryStarting new + starting retained + additions − all ending fuel retained, with no unaccounted spills/discards.Heat output, chemical burned mass or a complete balance when a fuel location is unmeasured.
Returned mass shareEnding retained fuel ÷ total starting-and-added fuel × 100.An energy-recovery percentage or equal usefulness of fresh and partly used fuel.
Rate for the named intervalChosen accounted mass ÷ hours inside the declared start/end boundary.A universal rate transferable to a different setup or interval.
An empty square metal pan with one handle
Locally generated illustration of an empty square metal pan with one handle.

Keep the source-specific limits attached

Traeger’s pellet support article calls its estimates approximations and lists grill size/model, pellet wood type, ambient temperature and lid openings among the variables. That supports recording those conditions; it does not prove how much any one condition changes your rate. The article does not turn two unmatched personal logs into an efficiency experiment. [1]

The Traeger Pro Series TFB57G/TFB78G manual DOC419V-A labels its procedure hopper cleanout and requires complete cooling before emptying it. A hopper collection is a hopper measurement: this procedure does not establish that the auger and firepot are empty. Follow the full manual for your exact cooker and do not handle or weigh hot fuel to complete a log. [3]

Weber’s New Zealand briquette guidance says leftover fuel may be reusable and discusses its mineral-char briquettes. Record starting retained fuel as well as new fuel if your exact cooker/fuel instructions permit reuse. That regional product guidance is not a blanket reuse instruction for every charcoal product or a claim that a pound of leftovers contains the energy of a pound of fresh fuel. [2]

Three hypothetical records, including an unknown result

On a narrow screen, scroll the table sideways to compare all columns.

Example A: entirely hypothetical complete boundary. All ending fuel locations are known; assume no spills, discarded fuel, added water or other unaccounted mass. This is not a hopper-only observation.
Input or resultInvented value / calculation
Starting new fuel; starting retained6 kg; 0 kg
Additions during this interval2 kg
Total ending retained fuel across the boundary2 kg
Accounted fuel not returned6 + 0 + 2 − 2 = 6 kg
Whole recorded interval6 hours, including startup and shutdown
Rate for that interval6 kg ÷ 6 h = 1.000 kg/h not returned
Different denominator, different rateIf food was present for only 5 h: 6 ÷ 5 = 1.200 kg/h per food-present hour. That is a different metric.

The 1.000 and 1.200 figures use the same invented fuel numerator. Their difference comes from changing the time denominator, not from a change in equipment performance. To compare two records, retain both clock boundaries and name which one the rate uses.

On a narrow screen, scroll the table sideways to compare all columns.

Example B: hypothetical charcoal inventory. New and previously retained fuel are both counted at the start; ending retained material is assumed to be usable fuel only, with no unaccounted discard/spill. No actual reuse performance is claimed.
Input or resultInvented value / calculation
New fuel at start; retained fuel at start4 kg new + 1 kg previously retained
Additions; ending retained fuel0 kg added; 1.5 kg retained at end
Fuel not returned4 + 1 + 0 − 1.5 = 3.5 kg
Rate over a 6-hour recorded interval3.5 ÷ 6 ≈ 0.583 kg/h not returned
New-fuel issue rate over the same interval4 ÷ 6 ≈ 0.667 kg/h new fuel issued
Returned mass share1.5 ÷ (4 + 1) × 100 = 30% of charged mass; not 30% of energy
Incorrect shortcut to reject4 − 1.5 = 2.5 kg omits the starting retained 1 kg.
A blank clipboard, pencil and empty metal tray on an outdoor table
Locally generated illustration of a blank clipboard, pencil and empty metal tray on an outdoor table.

On a narrow screen, scroll the table sideways to compare all columns.

Example C: hypothetical incomplete record. Pellet-grill fuel remaining is measured in the hopper only. The named manual’s cleanout scope explains why that is a limited boundary. [3]
Recorded itemValue / consequence
Starting total fuel; additions6 kg and 2 kg, assumed known
Ending hopper fuel2 kg
Ending auger / firepot fuelUnknown; no whole-system ending inventory
Tempting arithmetic6 + 2 − 2 = 6 kg is not a complete whole-system result.
Whole-system fuel not returned / rateUnknown. Do not put 6 kg or 1 kg/h in the result field.
Useful retained recordKeep the known inputs, exact hopper measurement, missing locations and clock times for later review.

Record what was actually weighed, including the container/tare, scale resolution and whether a mass is estimated. Keep ash, debris and unusable material separate from a usable-fuel return. If you cannot reliably separate or account for material at your chosen boundary, preserve that limit and stop the whole-system calculation. Do not dismantle a cooker outside its instructions to chase a complete number.

Use a fresh copy for each cook

Blank repeatable cook and fuel record

Fill a new record each time. Follow the exact cooker’s full instructions and record only safely obtained measurements. Unmeasured values stay blank; do not prefill a consumption rate.

These entries are personal notes. They are not sent to a restaurant or submitted to this site.

No hypothetical values belong in your observed column.

Include relevant accessories and configuration.

Keep new and retained fuel identities distinct.

State whether hopper, auger, firepot or other locations are covered.

Identify estimated versus directly observed values.

Record mass and its basis.

Do not silently treat it as zero.

Include new or retained identity and mass.

Mark unmeasured locations explicitly.

Separate locations and avoid double-counting ending fuel.

Record mass or leave the accounting incomplete.

Name the interval used for each rate.

Do not equate a setpoint with a measured temperature.

Keep observations and estimates distinct.

Record the setup you would need to reproduce.

Record the observed count or uncertainty.

Keep material changes visible.

Unknown if the chosen boundary is incomplete.

Transfer cautiously; name every material difference.

An open metal pot and empty shallow tray with a cooker behind them
Locally generated illustration of an open metal pot and empty shallow tray with a cooker behind them.

Check comparability before reusing the rate

  1. Same question and mass boundary? If one record is hopper-only and the other covers all fuel locations, stop the whole-system comparison.
  2. Complete inputs, same mass units and similar measurement resolution? Missing retained starting fuel, unknown ending fuel or unrecorded discards block that calculation.
  3. Same time boundary? Startup-through-shutdown and food-present time must remain separately named; recalculate only when the required times are known.
  4. Same cooker, configuration and fuel identity? Record differences rather than treating a changed setup as the same trial.
  5. Comparable temperature programme, weather, load and openings? If these differ, describe the records as different conditions; do not assign the result to a single cause.
  6. Checks sufficiently aligned for your planning purpose? Use the result as a conditional personal input, retain its date and limits, and gather more comparable records before treating it as stable.

Once a rate has a clear boundary and conditions, it can inform your own planning. The pellet consumption calculator estimates forward from an input; the ownership-cost worksheet uses fuel assumptions in a budget. This log preserves the evidence behind an input rather than supplying a universal replacement rate.

Sources and method

  1. Traeger Pellets support article and listed estimate variables
    Source checked · support.traeger.com
  2. Weber New Zealand mineral-char briquette quantities guidance
    Source checked · anz.weber.com
  3. Traeger Pro TFB57G/TFB78G DOC419V-A hopper cleanout
    Source checked · traegergrills.a.bigcontent.io

How this article is prepared

Researched and drafted with AI assistance from the cited sources. Examples and calculations retain their stated assumptions; illustrations do not establish restaurant visits or equipment tests.

About BBQ Explorer

Newest articles